MAGNETIX

ML-CONNECT-BK

Track Connector for two track sections for added stability.

Can be used to connect tracks for recess/surface/pendant style. Pin It Houzz

ML-CSM-CR-KIT-BLK

Curved track recess kit for mounting

Tracks are sold separately Pin It

ML-ENDCAP

Track end cap
Sold as 1 per unit

To be used to close up end of track, if no end cap is included. Pin It

ML-PENDT-CABLE-KIT-BK

Track Pendant Support Kit Without Canopy

Pin It

ML-PENDT-KIT-BK

*Tracks Sold Separately* Pin It

ML-PENDT-WIRE-KIT-BK

*Tracks Sold Separately* Pin It

ML-PIN4

Pins (set of 2) For Tracks Power Connection Pin It

ML-REC-KIT

Recess Kit Pin It

ML100W-BK-DRIVER

The LED driver must remain accessible for future maintenance or replacement.

Dimmable LED Driver (5 in 1 Dimming)
Triac/Phase, 1-10v, Potentionmeter
10V PWM 5 in 1 dimming
Constant Voltage
Input: 100-277V-1.5A max.
50/60Hz
Output: 24V - 4.17A

1-10V
The LED driver is controlled by an external signal between 1 and 10V. Perfectly dimmable in a range from 10% to 100%. Applicable with many home automation systems. It is necessary to place a 1-10V actuator between the home automation system and the fixture. Two extra control wires are needed to connect 1-10V.

Measurements:
18" Long
2.5" Wide
1" Deep
2 pounds Pin It

ML111-RM-BK

This is the corner to use for making rectangles Pin It

ML112-RM-BK

L-Corner for going from WALL to WALL in same room to make L shape, box, rectangle. Pin It

ML113-RM-BK

L-Corner for going from one wall to OUTER wall Pin It

ML150W-BK-DRIVER

The LED driver must remain accessible for future maintenance or replacement.

Dimmable LED Driver (5 in 1 Dimming)
Triac/Phase, 1-10v, Potentionmeter
10V PWM 5 in 1 dimming
Constant Voltage
Input: 100-277V-1.5A max.
50/60Hz
Output: 24V - 4.17A

1-10V
The LED driver is controlled by an external signal between 1 and 10V. Perfectly dimmable in a range from 10% to 100%. Applicable with many home automation systems. It is necessary to place a 1-10V actuator between the home automation system and the fixture. Two extra control wires are needed to connect 1-10V.

Measurements:
18" Long
2.5" Wide
1" Deep
2 Pounds Pin It

ML24080W-DRIVER-R

The LED driver must remain accessible for future maintenance or replacement. Do not install the driver above inaccessible dropped ceilings or inside partition walls.

Dimmable LED Driver (5 in 1 Dimming)
Triac/Phase, 1-10v, Potentionmeter
10V PWM 5 in 1 dimming
Constant Voltage
Input: 100-277V-1.15A max.
50/60Hz 0.95
Output: 24V - 3.33A 80W

1-10V
The LED driver is controlled by an external signal between 1 and 10V. Perfectly dimmable in a range from 10% to 100%. Applicable with many home automation systems. It is necessary to place a 1-10V actuator between the home automation system and the fixture. Two extra control wires are needed to connect 1-10V.

Measurements:
8" Long
4" Wide
1.5" Deep
2.5 Pounds Pin It

ML24100W-DRIVER-R

The LED driver must remain accessible for future maintenance or replacement. Do not install the driver above inaccessible dropped ceilings or inside partition walls.

Dimmable LED Driver (5 in 1 Dimming)
Triac/Phase, 1-10v, Potentionmeter
10V PWM 5 in 1 dimming
Constant Voltage
Input: 100-277V-1.5A max.
50/60Hz 0.95
Output: 24V - 4.17A 100W

1-10V
The LED driver is controlled by an external signal between 1 and 10V. Perfectly dimmable in a range from 10% to 100%. Applicable with many home automation systems. It is necessary to place a 1-10V actuator between the home automation system and the fixture. Two extra control wires are needed to connect 1-10V.

Measurements:
8" Long
4" Wide
1.5" Deep
2.5 Pounds Pin It

ML24150W-DRIVER-R

The LED driver must remain accessible for future maintenance or replacement. Do not install the driver above inaccessible dropped ceilings or inside partition walls.

Dimmable LED Driver (5 in 1 Dimming)
Triac/Phase, 1-10v, Potentionmeter
10V PWM 5 in 1 dimming
Constant Voltage
Input: 100-277V-1.8A max.
50/60Hz 0.95
Output: 24V - 6.25A 150W

1-10V
The LED driver is controlled by an external signal between 1 and 10V. Perfectly dimmable in a range from 10% to 100%. Applicable with many home automation systems. It is necessary to place a 1-10V actuator between the home automation system and the fixture. Two extra control wires are needed to connect 1-10V.

Measurements:
9.5" Long
4" Wide
2" Deep
4 Pounds Pin It

ML24200W-DRIVER-R

The LED driver must remain accessible for future maintenance or replacement. Do not install the driver above inaccessible dropped ceilings or inside partition walls.

Dimmable LED Driver (5 in 1 Dimming)
Triac/Phase, 1-10v, Potentionmeter
10V PWM 5 in 1 dimming
Constant Voltage
Input: 100-277V-2.3A max.
50/60Hz 0.95
Output: 24V - 8.33A 200W

1-10V
The LED driver is controlled by an external signal between 1 and 10V. Perfectly dimmable in a range from 10% to 100%. Applicable with many home automation systems. It is necessary to place a 1-10V actuator between the home automation system and the fixture. Two extra control wires are needed to connect 1-10V.

Measurements:
9.5" Long
4" Wide
2" Deep
4 Pounds Pin It

ML60W-BK-DRIVER

The LED driver must remain accessible for future maintenance or replacement.

Dimmable LED Driver (5 in 1 Dimming)
Triac/Phase, 1-10v, Potentionmeter
10V PWM 5 in 1 dimming
Constant Voltage
Input: 100-277V-1.5A max.
50/60Hz
Output: 24V - 4.17A

1-10V
The LED driver is controlled by an external signal between 1 and 10V. Perfectly dimmable in a range from 10% to 100%. Applicable with many home automation systems. It is necessary to place a 1-10V actuator between the home automation system and the fixture. Two extra control wires are needed to connect 1-10V.

Measurements:
15" Long
2.5" Wide
1" Deep
1.5 Pounds Pin It